sane-u12(5)              SANE Scanner Access Now Easy              sane-u12(5)

       sane-u12  -  SANE  backend  for  Plustek USB flatbed scanners, based on
       older parport designs

       The sane-u12 library implements a SANE (Scanner Access Now Easy)  back-
       end  that  provides  access  to USB flatbed scanners based on Plusteks'
       ASIC 98003 (parallel-port  ASIC)  and  a  GeneSys  Logics'  USB-parport
       bridge chip.

       The  backend  is  able  to support some early Plustek USB scanner based
       their old parport design around the ASIC 98003 and other rebadged Plus-
       tek devices. The following tables will give you a short overview.

       If  your Plustek scanner has another Product ID, then the device is NOT
       supported by this backend.

       Vendor Plustek - ID: 0x07B3
       Model:                   Vendor-ID:       Product-ID:
       OpticPro U12             0x07B3           0x0001
       OpticPro U1212           0x07B3           0x0001
       OpticPro UT12            0x07B3           0x0001

       Vendor KYE/Genius
       USB Model:               Vendor-ID:       Product-ID:
       ColorPage Vivid III USB  0x07B3           0x0001
       ColorPage HR6 V1         0x0458           0x2004

       To use your scanner with this backend, you need at least two entries in
       the configuration file @CONFIGDIR@/u12.conf
              [usb] vendor-id product-id
              device /dev/usbscanner

       [usb]  tells the backend, that the following devicename (here /dev/usb-
       scanner) has to be interpreted as USB scanner device.  If  vendor-  and
       product-id  has not been specified, the backend tries to detect this by
       its own. If device is set to auto then  the  next  matching  device  is

       The Options:

       option warmup t
              t specifies the warmup period in seconds

       option lampOff t
              t  is the time in seconds for switching off the lamps in standby

       option lOffonEnd b
              b specifies the behaviour when closing the backend, 1 --> switch
              lamps off, 0 --> do not change lamp status

       See the u12.conf file for examples.

       You  have  to make sure, that the USB subsystem is loaded correctly and
       you have access to the device-node. For more details see  sane-usb  (5)
       manpage.  You might use sane-find-scanner to check that you have access
       to your device.

       If there's no configuration file, the backend defaults to device auto

              The backend configuration file

              The static library implementing this backend.

              The shared library implementing this backend (present on systems
              that support dynamic loading).

              This environment variable specifies the list of directories that
              may contain the configuration file.  Under UNIX, the directories
              are  separated  by a colon (`:'), under OS/2, they are separated
              by a semi-colon (`;').  If this variable is not set, the config-
              uration  file is searched in two default directories: first, the
              current working directory (".") and then in @CONFIGDIR@.  If the
              value  of the environment variable ends with the directory sepa-
              rator character, then the default directories are searched after
              the  explicitly  specified  directories.   For  example, setting
              SANE_CONFIG_DIR to "/tmp/config:" would  result  in  directories
              "tmp/config", ".", and "@CONFIGDIR@" being searched (in this or-

              If the library was compiled with debug support enabled, this en-
              vironment  variable  controls  the debug level for this backend.
              Higher debug levels increase the verbosity of the output.

              Example: export SANE_DEBUG_U12=10

       sane(7), sane-usb(5), sane-plustek(5),

       Please send any information and bug-reports to:
       SANE Mailing List

       Additional info and hints can be obtained from our
       Mailing-List archive at:

       To obtain debug messages from the backend, please set the  environment-
       variable  SANE_DEBUG_U12  before  calling  your  favorite scan-frontend
       (i.e. xscanimage).
       i.e.: export SANE_DEBUG_U12=20 ; xscanimage

       The value controls the verbosity of the backend.

       * The driver is in alpha state, so please don't expect too much!!!

       * When using libusb, it might be, that  the  backend  hangs.   In  that
       case, reconnect the scanner.

@PACKAGEVERSION@                  14 Jul 2008                      sane-u12(5)
Man Pages Copyright Respective Owners. Site Copyright (C) 1994 - 2024 Hurricane Electric. All Rights Reserved.