sane-snapscan(5)         SANE Scanner Access Now Easy         sane-snapscan(5)

       sane-snapscan - SANE backend for AGFA SnapScan flatbed scanners

       The  sane-snapscan  library implements a SANE (Scanner Access Now Easy)
       backend that provides access to  AGFA  SnapScan  flatbed  scanners.  At
       present,  the  following scanners are supported from this backend: AGFA
       SnapScan 300, 310, 600, and 1236s, 1236u, 1212u, e20,  e25,  e40,  e50,
       e60,  Vuego  310s,  Acer  300f,  310s, 610s, 610plus, Prisa 620s, Prisa
       620u, Prisa 620ut, Prisa 640u, Prisa 640bu,  Prisa  1240,  Prisa  3300,
       Prisa  4300,  Prisa 5300 and Guillemot Maxi Scan A4 Deluxe (SCSI) (with
       varying success).

       This backend expects device names of the form:


       Where special is the path-name for the special device that  corresponds
       to a SCSI scanner. For SCSI scanners, the special device name must be a
       generic SCSI device or a symlink to such a device.  Under Linux, such a
       device   name   could  be  /dev/sga  or  /dev/sge,  for  example.   See
       sane-scsi(5) for details.

       For USB scanners the devicename must contain the keyword "usb",  as  in
       /dev/usbscanner   or  /dev/usb/scanner0.   For  scanners  that  need  a
       firmware upload before scanning add a  line  starting  with  "firmware"
       followed by the fully qualified path to your firmware file, e.g.

              firmware @DATADIR@/sane/snapscan/firmware.bin

       For further details read

       The  contents  of the snapscan.conf file is a list of device names that
       correspond to SnapScan scanners.  Empty lines and lines starting with a
       hash mark (#) are ignored.  See sane-scsi(5) on details of what consti-
       tutes a valid device name.

              The  backend  configuration  file  (see  also   description   of
              SANE_CONFIG_DIR below).

              The static library implementing this backend.

              The shared library implementing this backend (present on systems
              that support dynamic loading).

              This environment variable specifies the list of directories that
              may contain the configuration file.  Under UNIX, the directories
              are separated by a colon (`:'), under OS/2, they  are  separated
              by a semi-colon (`;').  If this variable is not set, the config-
              uration file is searched in two default directories: first,  the
              current working directory (".") and then in @CONFIGDIR@.  If the
              value of the environment variable ends with the directory  sepa-
              rator character, then the default directories are searched after
              the explicitly  specified  directories.   For  example,  setting
              SANE_CONFIG_DIR  to  "/tmp/config:"  would result in directories
              "tmp/config", ".", and "@CONFIGDIR@" being searched (in this or-

              If the library was compiled with debug support enabled, this en-
              vironment variable controls the debug level  for  this  backend.
              E.g.,  a  value  of 255 requests all debug output to be printed.
              Smaller levels reduce verbosity.

       Man page doesn't provide much information yet.

       sane(7), sane-scsi(5) (new development website)

       Kevin Charter, Franck Schneider, Michel Roelofs, Emmanuel  Blot,  Mikko
       Tyolajarvi,  David  Mosberger-Tang, Wolfgang Goeller, Petter Reinholdt-
       sen, Gary Plewa, Sebastien Sable, Oliver Schwartz and Mikael Magnusson.
       Man page by Henning Meier-Geinitz (mostly based on the  web  pages  and
       source code).

@PACKAGEVERSION@                  14 Jul 2008                 sane-snapscan(5)
Man Pages Copyright Respective Owners. Site Copyright (C) 1994 - 2024 Hurricane Electric. All Rights Reserved.