ip-rule

IP-RULE(8)                           Linux                          IP-RULE(8)

NAME
       ip-rule - routing policy database management

SYNOPSIS
       ip [ OPTIONS ] rule { COMMAND | help }

       ip rule [ list [ SELECTOR ]]

       ip rule { add | del } SELECTOR ACTION

       ip rule { flush | save | restore }

       SELECTOR := [ not ] [ from PREFIX ] [ to PREFIX ] [ tos TOS ] [ fwmark
               FWMARK[/MASK] ] [ iif STRING ] [ oif STRING ] [ pref NUMBER ] [
               l3mdev ] [ uidrange NUMBER-NUMBER ] [ ipproto PROTOCOL ] [
               sport [ NUMBER | NUMBER-NUMBER ] ] [ dport [ NUMBER | NUMBER-
               NUMBER ] ] [ tun_id TUN_ID ]

       ACTION := [ table TABLE_ID ] [ protocol PROTO ] [ nat ADDRESS ] [
               realms [SRCREALM/]DSTREALM ] [ goto NUMBER ] SUPPRESSOR

       SUPPRESSOR := [ suppress_prefixlength NUMBER ] [ suppress_ifgroup GROUP
               ]

       TABLE_ID := [ local | main | default | NUMBER ]

DESCRIPTION
       ip rule manipulates rules in the routing policy database control the
       route selection algorithm.

       Classic routing algorithms used in the Internet make routing decisions
       based only on the destination address of packets (and in theory, but
       not in practice, on the TOS field).

       In some circumstances we want to route packets differently depending
       not only on destination addresses, but also on other packet fields:
       source address, IP protocol, transport protocol ports or even packet
       payload.  This task is called 'policy routing'.

       To solve this task, the conventional destination based routing table,
       ordered according to the longest match rule, is replaced with a 'rout-
       ing policy database' (or RPDB), which selects routes by executing some
       set of rules.

       Each policy routing rule consists of a selector and an action predi-
       cate.  The RPDB is scanned in order of decreasing priority (note that
       lower number means higher priority, see the description of PREFERENCE
       below). The selector of each rule is applied to {source address, desti-
       nation address, incoming interface, tos, fwmark} and, if the selector
       matches the packet, the action is performed. The action predicate may
       return with success.  In this case, it will either give a route or
       failure indication and the RPDB lookup is terminated. Otherwise, the
       RPDB program continues with the next rule.

       Semantically, the natural action is to select the nexthop and the out-
       put device.

       At startup time the kernel configures the default RPDB consisting of
       three rules:

       1.     Priority: 0, Selector: match anything, Action: lookup routing
              table local (ID 255).  The local table is a special routing ta-
              ble containing high priority control routes for local and broad-
              cast addresses.

       2.     Priority: 32766, Selector: match anything, Action: lookup rout-
              ing table main (ID 254).  The main table is the normal routing
              table containing all non-policy routes. This rule may be deleted
              and/or overridden with other ones by the administrator.

       3.     Priority: 32767, Selector: match anything, Action: lookup rout-
              ing table default (ID 253).  The default table is empty. It is
              reserved for some post-processing if no previous default rules
              selected the packet.  This rule may also be deleted.

       Each RPDB entry has additional attributes. F.e. each rule has a pointer
       to some routing table. NAT and masquerading rules have an attribute to
       select new IP address to translate/masquerade. Besides that, rules have
       some optional attributes, which routes have, namely realms.  These val-
       ues do not override those contained in the routing tables. They are
       only used if the route did not select any attributes.

       The RPDB may contain rules of the following types:

              unicast - the rule prescribes to return the route found in the
              routing table referenced by the rule.

              blackhole - the rule prescribes to silently drop the packet.

              unreachable - the rule prescribes to generate a 'Network is un-
              reachable' error.

              prohibit - the rule prescribes to generate 'Communication is ad-
              ministratively prohibited' error.

              nat - the rule prescribes to translate the source address of the
              IP packet into some other value.

       ip rule add - insert a new rule

       ip rule delete - delete a rule

              type TYPE (default)
                     the type of this rule. The list of valid types was given
                     in the previous subsection.

              from PREFIX
                     select the source prefix to match.

              to PREFIX
                     select the destination prefix to match.

              iif NAME
                     select the incoming device to match. If the interface is
                     loopback, the rule only matches packets originating from
                     this host. This means that you may create separate rout-
                     ing tables for forwarded and local packets and, hence,
                     completely segregate them.

              oif NAME
                     select the outgoing device to match. The outgoing inter-
                     face is only available for packets originating from local
                     sockets that are bound to a device.

              tos TOS

              dsfield TOS
                     select the TOS value to match.

              fwmark MARK
                     select the fwmark value to match.

              uidrange NUMBER-NUMBER
                     select the uid value to match.

              ipproto PROTOCOL
                     select the ip protocol value to match.

              sport NUMBER | NUMBER-NUMBER
                     select the source port value to match. supports port
                     range.

              dport NUMBER | NUMBER-NUMBER
                     select the destination port value to match. supports port
                     range.

              priority PREFERENCE
                     the priority of this rule.  PREFERENCE is an unsigned in-
                     teger value, higher number means lower priority, and
                     rules get processed in order of increasing number. Each
                     rule should have an explicitly set unique priority value.
                     The options preference and order are synonyms with prior-
                     ity.

              table TABLEID
                     the routing table identifier to lookup if the rule selec-
                     tor matches.  It is also possible to use lookup instead
                     of table.

              protocol PROTO
                     the routing protocol who installed the rule in question.
                     As an example when zebra installs a rule it would get RT-
                     PROT_ZEBRA as the installing protocol.

              suppress_prefixlength NUMBER
                     reject routing decisions that have a prefix length of
                     NUMBER or less.

              suppress_ifgroup GROUP
                     reject routing decisions that use a device belonging to
                     the interface group GROUP.

              realms FROM/TO
                     Realms to select if the rule matched and the routing ta-
                     ble lookup succeeded. Realm TO is only used if the route
                     did not select any realm.

              nat ADDRESS
                     The base of the IP address block to translate (for source
                     addresses).  The ADDRESS may be either the start of the
                     block of NAT addresses (selected by NAT routes) or a lo-
                     cal host address (or even zero).  In the last case the
                     router does not translate the packets, but masquerades
                     them to this address.  Using map-to instead of nat means
                     the same thing.

                     Warning: Changes to the RPDB made with these commands do
                     not become active immediately. It is assumed that after a
                     script finishes a batch of updates, it flushes the rout-
                     ing cache with ip route flush cache.

       ip rule flush - also dumps all the deleted rules.

              protocol PROTO
                     Select the originating protocol.

       ip rule show - list rules
              This command has no arguments.  The options list or lst are syn-
              onyms with show.

       ip rule save

              protocol PROTO
                     Select the originating protocol.

       save rules table information to stdout
              This command behaves like ip rule show except that the output is
              raw data suitable for passing to ip rule restore.

       ip rule restore
              restore rules table information from stdin
              This command expects to read a data stream as returned from ip
              rule save.  It will attempt to restore the rules table informa-
              tion exactly as it was at the time of the save. Any rules al-
              ready in the table are left unchanged, and duplicates are not
              ignored.

SEE ALSO
       ip(8)

AUTHOR
       Original Manpage by Michail Litvak <mci@owl.openwall.com>

iproute2                          20 Dec 2011                       IP-RULE(8)
Man Pages Copyright Respective Owners. Site Copyright (C) 1994 - 2024 Hurricane Electric. All Rights Reserved.