This manpage has been automatically generated from fdutils's texinfo
documentation. However, this process is only approximative, and some
items, such as cross-references, footnotes and indices are lost in this
translation process. Indeed, these items have no appropriate represen-
tation in the manpage format. Moreover, only the items specific to
each command have been translated, and the general information about
fdutils has been dropped in the manpage version. Thus I strongly
advise you to use the original texinfo doc.
* To generate a printable copy from the texinfo doc, run the fol-
./configure; make dvi; dvips fdutils.dvi
* To generate a HTML copy, run:
./configure; make html
A pre-made HTML can be found at:
* To generate an info copy (browsable using emacs' info mode),
./configure; make info
The texinfo doc looks most pretty when printed or as HTML. Indeed, in
the info version certain examples are difficult to read due to the
quoting conventions used in info.
fdmount [-l] [--list] [-d] [--daemon] [--detach]
[-i interval] [--interval interval] [-o mount-options]
[-r] [-readonly] [-s] [--sync] [--nosync] [--nodev]
[--nosuid] [--noexec] [-f] [--force] [-h] [--help]
fdumount [-f] [--force] [drivename]
fdmountd [-i interval] [--interval interval] [-r]
[-readonly] [-s] [--sync] [--nosync] [--nodev]
[--nosuid] [--noexec] [--help] [drivename] [mountpoint]]
The symbolic drivename is (currently) one of `fd[0-7]', corresponding
to the special device files `/dev/fd[0-7]'. If drivename is not speci-
fied, `fd0' is assumed.
The disk is mounted on the directory mountpoint, if specified, or on
`/fd[0-7]'. In either case, the mount point must be an existing,
Due to a bug in the floppy driver (?), the polling interval (-i flag)
must be longer than the spindown offset. Thus you need to do (for exam-
ple) floppycontrol --spindown 99 before starting fdmountd in daemon
List all known drives with their symbolic name, type, and mount
Run in daemon mode (see below).
Runs daemon in background, and detaches it from its tty. Mes-
sages produced after the fork are logged to syslog.
Dumps the process id of the daemon to file. This makes killing
the daemon easier: kill -9 `cat file`
Set the polling interval for daemon mode. The unit for interval
is 0.1 seconds, the default value is 10 (i.e. 1 second).
Sets filesystem-specific options. So far, these are only avail-
able for DOS and Ext2 disks. The following DOS options are sup-
ported: check, conv, dotsOK, debug, fat, quiet, blocksize. The
following Ext2 options are supported: check, errors, grpid, bsd-
groups, nogrpid, sysvgroups, bsddf, minixdf, resgid, debug,
nocheck. When running as a daemon, options not applying to the
disk that is inserted (because of its filesystem type) are not
passed to mount.
Mount the disk read-only. This is automatically assumed if the
disk is write protected.
Mount with the NOEXEC option.
Attempt a mount or unmount operation even `/etc/mtab' says that
the drive is already mounted, or not mounted, respectively.
This option is useful if `/etc/mtab' got out of sync with the
actual state for some reason.
Show short parameter description
When mounting on the default mount point, the mount points' owner is
set to the current user, and the access flags according to the user's
umask. For a specified mountpoint, owner and permissions are left
unchanged. Default mount points are called /fd0, /fd1, ... , /fd7.
The user running fdmount must have read access to the floppy device for
read only mounts, and read/write access for read/write mounts.
Fdmount can be run suid root, allowing users to mount floppy disks. The
following restrictions are placed upon non-root users:
* If a mountpoint is specified explicitly, it must be owned by the
* A user may only unmount a disk if the mount point is owned by
the user, or if it the disk has been mounted by the same user.
* Non-msdos disks are automatically mounted with the nodev and
nosuid flags set.
However, do not rely on fdmount being secure at the moment.
In daemon mode, the specified drive is periodically checked and if a
disk is inserted, it is automatically mounted.
When the disk is removed, it is automatically unmounted. However, it
is recommended to unmount the disk manually before removing it. In
order to limit corruption, disks are mounted with the SYNC option when
running in daemon mode, unless the --nosync flag is given.
Note that this mode has some potential drawbacks:
* Some floppy drives have to move the drive head physically in
order to reset the disk change signal. It is strongly recom-
mended not to use daemon mode with these drives. See section
floppycontrol, for details.
* If a disk does not contain a filesystem (e.g. a tar archive),
the mount attempt may slow down initial access.
unknown filesystem type
No magic number of any of the supported filesystems (see above)
could be identified.
sorry, can't figure out format (fs filesystem)
The size of the filesystem on the disk is incompatible with the
track layout detected by the kernel and an integer number of
tracks. This may occur if the filesystem uses only part of the
disk, or the track layout was detected incorrectly by the ker-
failed to mount fs> <sizeK-disk
The actual mount system call failed.
failed to unmount
The actual unmount system call failed.
cannot create lock file /etc/mtab~
If `/etc/mtab~' exists, you should probably delete it. Other-
wise, check permissions.
Can't access mountpoint
Most probably, the default or specified mount point does not
exist. Use mkdir.
mountpoint is not a directory
The mountpoint is not a directory.
not owner of mountpoint
Non-root users must own the directory specified as mount point.
(This does not apply for the default mount points, /fd[0-3].)
No write permission to mountpoint
Non-root users must have write permission on the mount point
Not owner of mounted directory: UID=uid
Non-root users cannot unmount if the mount point is owned (i.e.
the disk was mounted) by another user.
invalid drive name
Valid drive names are `fd0', `fd1', etc.
drive name does not exist
The drive does not exist physically, is unknown to the Linux
kernel, or is an unknown type.
Drive name is mounted already
Trying to mount a drive which appears to be mounted already.
Use the --force option if you think this is wrong.
Drive name is not mounted
Trying to unmount a drive which does not appear to be mounted.
* Probably not very secure yet (when running suid root). Untested
with ext and xia filesystems.
* Can't specify filesystem type and disk layout explicitly.
* In daemon mode, the drive light stays on all the time.
* Some newer filesystem types, such as vfat are not yet supported.
Fdutils' texinfo doc
fdutils-5.5 03Mar05 fdmount(1)
Man Pages Copyright Respective Owners. Site Copyright (C) 1994 - 2018
All Rights Reserved.